Technology · Patent pending

One converter. The whole span.

An analogue-to-digital converter measures within a fixed window. The Metere Decimator takes a signal far wider than that window through one converter per channel and delivers it at one level, with no clipping, to whatever comes next. Patent pending.

Signal acquisition · Patent pending

Metere Decimator

A converter’s window runs from its full scale down to its own noise: about 75 dB for the fast converters used at baseband. The signals a receiver has to take in are wider. On an uplink, a user at the cell edge arrives near −100 dBm (decibels relative to one milliwatt), a user beside the base station near −30 dBm, and an adjacent-channel transmitter stronger still. Until now the span has been covered by automatic gain control that reacts after the signal has moved, by two or more converters at different gains with their outputs stitched together, or by a gain update confined to a guard period and applied as a step that the baseband has to tolerate. The Metere Decimator is another way.

Converters
One per channel, one analogue path
Span, example in the application
108 dB from a 75 dB converter
Delivered level
One scale across every gain change
Sampling rate
Any, hertz to gigahertz

What it does

Wide in, one level out.

Every property below is observable at the output. What happens inside is patent pending.

1

Converter per channel

One converter and one analogue path. No parallel converters at different gains, no stitching of their outputs.

0

Steps at the demodulator

The delivered stream has the same scale before and after every gain change. Channel estimator, equaliser, carrier and timing recovery loops see no step.

+

Gain range added to converter range

In the example in the application, a 75 dB converter behind a two-setting front end 40 dB apart delivers 108 dB: full scale at +10 dBm at the antenna, floor at −98 dBm, the receiver’s own thermal noise.

N

Noise floor of every sample, reported

The baseband is told, sample by sample, where the floor is. A soft-decision decoder can use it as a per-sample reliability.

=

Constant relative gains across antennas

With one converter per antenna, every channel is delivered on the same scale, so combining and beamforming see fixed relative gains.

0

Samples clipped

For an input band-limited to the receiver’s own bandwidth, no sample is clipped: a result with a proof behind it, and the simulation agrees in every case. This guarantee is itself patent pending, as Zero-Clip Gain Control.

Results so far

Four hostile cases, no sample lost.

Simulation at 245.76 megasamples per second on 20 MHz multi-carrier traffic with 64 subcarriers, whose envelope is almost never quiet, through the receive filter, with the controller that is now in logic. Hardware results will be published as they are measured.

  • Case 1

    Near-far packets

    Alternating slots from a far user at −80 dBm and a near user at −6 dBm, 2 µs guard intervals, 1 µs power ramps. Every return to the sensitive setting lands inside a guard interval. No sample lost.

  • Case 2

    Near user ramps up on a far user

    A near user’s carrier ramps up over 20 µs on top of a far user received continuously, with no gap anywhere. One change, made under traffic as it must be, no sample lost, the far user received at full sensitivity until then.

  • Case 3

    Deep fade and recovery

    One carrier at −6 dBm whose envelope fades by 40 dB and recovers over 50 µs. Received throughout without a change and without a sample lost.

  • Case 4

    Radar return

    A 1 µs pulse followed by twelve echoes whose power falls with the fourth power of range to 60 dB down. Three changes, two of them placed in the dead time between echoes, no sample lost.

Where it applies

Wherever a converter meets a signal wider than its window.

The method is not tied to a sampling rate or to a kind of signal. Every quantity in it is a count of samples or a fraction of full scale, so the same controller runs unchanged at any rate, with a converter of any architecture.

RF

Cellular and wireless receivers

The near-far span of a multi-user uplink, the onset and lifting of fades, and a strong adjacent-channel signal, with one converter per antenna. Software-defined radio included.

SerDes

Wireline and high-speed serial links

The converter-based receiver of a high-speed serial link runs a time-interleaved converter of a few bits behind a variable-gain stage, ahead of an equaliser and a clock recovery loop that depend on a constant gain from the input. They receive one level across every gain change, with a bounded delivery latency, from a converter of any architecture including time-interleaved, at any rate from hertz to gigahertz.

Echo

Radar, sonar, lidar, ultrasound

The received echo falls in power with range. Near and far returns are delivered on one scale through one converter.

T&M

Instrumentation and test

Acquisition whose source range exceeds the converter’s, delivered without a step for the stages that follow.

Sense

Sensing and detector readout

Seismic, biomedical, optical and particle-detector signals whose dynamic range exceeds the converter’s window.

Any

Any rate, any architecture

Delta-sigma, successive-approximation, pipelined, flash and time-interleaved converters, from hertz to gigahertz.

Status

Patent pending. Open to licensing.

The Metere Decimator and Zero-Clip Gain Control are both patent pending. Both are available for licensing, and for evaluation under a non-disclosure agreement.

Start a conversation →